Olympia Chimney Flue Liner Replacement Nationwide

Olympia Chimney Flue Liner Replacement: The White Plains Owner’s Guide

An Olympia Chimney flue liner replacement in White Plains typically runs $2,800-$5,400 installed, depending on the height of your chimney, the diameter needed, and whether the existing liner pulls out cleanly or has to be cut out in sections. We stock Olympia Chimney-compatible stainless steel liners in the common 6-inch and 8-inch diameters on our trucks, and most replacements in White Plains are completed in a single day. Homeowners usually discover the problem during a routine sweep when our camera finds gaps, corrosion, or flaking inside the liner, or when they notice bits of terracotta in the firebox and a smoky smell that wasn’t there last season.

Call (914) 603-1360

Which Olympia Chimney Models This Applies To

Olympia Chimney produces flexible stainless steel liners in several wall thicknesses and alloy grades, and matching the right replacement means reading the collar stamp or measuring what is actually in your flue now. The common series we see in White Plains homes are the 316Ti flexible liners (rated for wood, pellet, and oil) and the heavier AL29-4C alloy lines required for high-efficiency gas appliances. If your original liner was installed between 1995 and 2010, check the upper termination collar for a stamped series number; earlier installations often used unmarked 304-grade stainless that degrades faster in our freeze-thaw cycles.

We are an independent service provider, not affiliated with Olympia Chimney. For most White Plains replacements, we install OEM-equivalent 316Ti flexible liner from our stock, which matches Olympia’s specifications exactly and carries the same UL 1777 listing. The only time we insist on factory-direct Olympia Chimney liner is when your appliance warranty explicitly requires it, which we verify before quoting. A compatibility gotcha: some Gedney Farm-area colonials have offset flues that need a more flexible, thinner-wall liner to navigate the bend without creasing. We measure the offset angle on every job, because forcing a standard liner through a sharp offset creates a stress point that fails in three to five years.

Signs Your Olympia Chimney Flue Liner Replacement Is Failing

• Flakes of metal or clay in the firebox. These are pieces of the liner itself breaking down from creosote corrosion or thermal cycling. In White Plains, where heating seasons run long and appliances cycle hard, we see this most often in liners past fifteen years.
• Smoke backing up into the room on startup. A breached liner allows exhaust to escape through gaps into the chimney cavity before the draft establishes. This is not a draft problem you can fix with a damper adjustment.
• White or orange staining on exterior masonry. Condensation and acidic exhaust are leaking through liner gaps and leaching salts from the mortar. By the time you see this, the liner has been compromised for at least one heating season.
• A tar-like odor that lingers after the fire is out. This means creosote is accumulating in the chimney cavity outside the liner, where it cannot be reached by normal sweeping and poses a serious fire risk.
• Your carbon monoxide detector has sounded, even once. Any liner breach can allow CO into wall cavities or living spaces. This is not a sensor malfunction to ignore.

Replacement Cost & What’s Included

What drives the range: chimney height above the roofline, whether the existing liner is intact enough to pull or must be demolished in place, and access (steep roofs in the Highlands neighborhood add rigging time). Every quote includes a Level-2 camera inspection first, so you see the damage yourself before we order parts. No surprises on the bill. The liner carries a lifetime warranty; our workmanship is covered by the 90-Day Done Right Promise, in writing, no arguing.

DIY or Call Us?

There is exactly one thing a homeowner can safely check: shine a flashlight up the flue from the firebox and look for visible gaps, holes, or sagging sections. Do not attempt to remove or install a flue liner yourself. The old liner may be wedged in place with decades of creosote hardening around it, and pulling it without proper anchoring can damage the chimney structure or send a heavy section down on you unexpectedly. The new liner must be properly sized to the appliance, insulated to current NY building code, and terminated with a listed top assembly. Get any of this wrong and you have a chimney fire or carbon monoxide hazard, not a repair.

We carry Olympia Chimney-compatible liner on the truck in diameters from 5 to 10 inches. Call (914) 603-1360 and we will walk through what you are seeing, schedule a camera inspection if needed, and give you upfront pricing before any work begins. Most jobs are done in one visit. If the chimney’s doing its job, you won’t think about it. That’s exactly where we want to leave things.

FAQs