Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Cap & Crown in White Plains: What to Know First
As an independent Olympia Chimney service provider, we install, repair, and replace chimney caps and crowns on Olympia Chimney systems throughout White Plains. Most Olympia Chimney cap and crown jobs are completed in a single visit, with upfront pricing agreed before we start. We’re not the cheapest outfit in Westchester, and we don’t try to be - we quote the job to stay done.
This page is for homeowners who already have an Olympia Chimney product installed and need cap or crown work done right. If you’re in White Plains, Scarsdale, or the Gedney Farm area and your cap is rattling, your crown is cracking, or you’re not sure which you even have, call us at (914) 603-1360. A live person answers, 24 hours a day.
How Olympia Chimney Products Fail - and How We Fix Them
- Olympia Chimney 304 stainless single-flue caps: The mesh on these can clog with creosote faster than you’d expect, especially if you’re burning green or unseasoned wood in a White Plains winter. The cap overheats, warps at the seams, and eventually lifts off in a nor’easter. We pull the old cap, inspect the flue tile with a camera, and fit a replacement with wider mesh spacing where code allows - or switch you to a Gelco or Famco cap with better draw if the flue calls for it.
- Olympia Chimney multi-flue chimney caps (galvanized or stainless):strong> The mounting brackets on older galvanized units corrode at the bolt points after seven to ten years of freeze-thaw cycles. We’ve found this on colonials near Gedney Farm where the cap was installed in the early 2000s. We replace the bracket set with stainless hardware and seal the crown beneath before the new cap goes on - otherwise you’re back in two seasons.
- Olympia Chimney wind-directional caps: The rotating hood seizes when the bearing housing fills with soot and moisture. In White Plains, this happens most on north-facing chimneys that never fully dry out. We disassemble the hood, clean the bearing race, and repack with high-temp grease. If the housing is cracked, we source an OEM replacement or fabricate a fit from Copperfield components.
- Crown deterioration under Olympia Chimney caps: The cap itself is fine, but the poured concrete crown beneath it has spider-webbed from water trapped between cap and crown. Olympia Chimney caps sit close to the crown on some models, which limits airflow and extends drying time. We remove the cap, grind the crown back to sound concrete, apply a HeatShield crown coat, and reinstall with spacers for better ventilation.
- Olympia Chimney chase covers on prefab chimneys: The factory chase cover is often thin galvanized steel that rusts through at the corners first - we see this on 1990s builds in White Plains where the chase was never properly flashed. We measure for a custom-fabricated stainless or copper chase cover from Copperfield, cut the drip edge to shed water away from the siding, and seal with high-temp silicone. The prefab firebox stays dry, and you stop getting water stains on the ceiling.
Our Olympia Chimney Chimney Cap & Crown Process
- 1
Call and schedule. A live person answers, day or night. We ask what you’re seeing - water in the firebox, rust streaks on the brick, a cap that’s shifted or missing - and book a time that works. No app, no callback queue.
- 2
Level-2 camera inspection. Our tech arrives in uniform, background-checked, and sets up a camera inspection of the flue and crown. You see the photos on a tablet. We explain what’s wrong, what can wait, and what you don’t need at all. Russell Haines trained every tech to give the same plain-English verdict he’d give himself.
- 3
Parts decision. If your Olympia Chimney cap is under warranty and the failure is a manufacturing defect, we note that for your records. For out-of-warranty work, we quote OEM replacement or a quality aftermarket cap from Gelco, Famco, or Copperfield - whichever fits your flue configuration and budget. No builder-grade substitutes.
- 4
The repair. Most cap replacements and crown coatings are done in one visit. We protect your roof and landscaping, remove the old component, prep the surface, and install the new. Crown work gets a HeatShield slurry or troweled repair, cured before we leave.
- 5
Test and document. We run a draft test, check for leaks with a water hose simulation, and photo-document the finished work. You get a report with images, the work description, and your 90-Day Done Right Promise in writing.
- 6
Cleanup and close. We haul away the old cap or crown debris, sweep the work area, and review the invoice with you. The number on the estimate is the number on the invoice. No surprises.
What Olympia Chimney Chimney Cap & Crown Costs in White Plains
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Olympia Chimney single-flue cap replacement | $280 - $450 | Flue size, mesh type, roof access difficulty |
| Olympia Chimney multi-flue cap replacement | $480 - $780 | Width, stainless vs. galvanized, bracket condition |
| Crown repair with HeatShield coating | $650 - $1,100 | Crown size, crack depth, need for rebuild vs. coat |
| Chase cover replacement (prefab chimney) | $720 - $1,400 | Material (stainless vs. copper), chase height, flashing complexity |
| Wind-directional cap service or replacement | $340 - $620 | Bearing rebuild vs. full replacement, hood size |
These are real White Plains price ranges based on jobs we’ve done in the last two years - not bait-and-switch estimates. Steep roofs, buried access, or additional flue damage can push toward the higher end. We tell you before we start. Call (914) 603-1360 for a free, exact quote on your Olympia Chimney system.
Why White Plains Homeowners Call Hearthstone Chimney Co. for Olympia Chimney Work
We’ve been sweeping and repairing chimneys in White Plains since 1984. That’s long enough to know which houses near Gedney Farm have the original 1960s flue tiles, and which developments put in prefab units that are hitting their thirty-year mark now.
Our techs carry Olympia Chimney parts and compatible components from DuraFlex, HeatShield, Gelco, Famco, and Copperfield on the truck. If your cap size is discontinued or the OEM lead time is three weeks, we have alternatives that fit and perform - no waiting, no guesswork.
The 90-Day Done Right Promise means if it’s not right, we make it right. In writing. No paperwork to dig up, no arguing. We’ve honored it on crown coatings that cracked in an unusual cold snap, and on a cap that didn’t seat flush because the flue tile had settled. We came back, fixed it, and moved on. That’s how you stay in business for over 42 years.
If the chimney’s doing its job, you won’t think about it. That’s exactly where we want to leave things.
FAQs
No. As an independent Olympia Chimney service provider, our work does not void manufacturer warranties on the product itself. If your cap or crown failure is due to a manufacturing defect and your unit is still under warranty, we document our findings so you can file a claim with Olympia Chimney directly. We do not process warranty claims on their behalf. For out-of-warranty work, we handle the repair and back it with our own 90-Day Done Right Promise. Call (914) 603-1360 to discuss your specific unit.
We can source OEM Olympia Chimney caps and components when they’re available and when the price makes sense. We also stock quality aftermarket caps from Gelco, Famco, and Copperfield that match or exceed OEM specifications for mesh gauge, stainless grade, and wind load rating. On some older Olympia Chimney lines, the OEM part has been discontinued, and an aftermarket fit is your only practical option. We show you both choices and explain the difference. Call (914) 603-1360 for a free estimate.
If the mesh is intact and only the mounting hardware is corroded, we can often replace brackets and reseat the existing cap. If the hood is warped, the seams are split, or the mesh is rusted through, replacement is the better value - repairing a compromised cap usually costs nearly as much and leaves you with old metal. Our camera inspection shows you the condition so you can decide. Call (914) 603-1360 to schedule.
Most cap replacements are completed in a single visit once scheduled. We carry common Olympia Chimney and compatible cap sizes on our trucks. If your configuration requires a custom order, we typically have it within three to five business days. We do not promise same-day dispatch, but we do answer the phone 24/7 and schedule as promptly as the season allows. Call (914) 603-1360 to book.
The new cap will fail prematurely. Water trapped in a cracked crown freezes, expands, and pushes up through the cap mounting points or seeps past the seal. We’ve removed year-old caps that looked fine but were sitting on crumbling crowns underneath. We won’t install a new cap over a failing crown without explaining why - and we document the crown condition with photos so you can see it yourself. Call (914) 603-1360 for an honest assessment.
Ready to get your Olympia Chimney cap or crown sorted? Call (914) 603-1360 anytime - a live person will answer, and we’ll set up your free estimate at a time that works. We’ve been doing this in White Plains for over 42 years, and we plan to be here when your chimney needs us again.
Written by Russell Haines, Owner, Hearthstone Chimney Co. at Hearthstone Chimney Co., serving White Plains and nearby areas.